Fortress Technologies ecure Wireless Access Bridge Manuel d'utilisateur Page 58
- Page / 144
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Fortress Bridge: Configuration
48
To enable/disable blackout mode:
1 Log on to the Bridge GUI admin account and select SYSTEM
OPTIONS from the menu on the left.
2 Under BLACKOUT MODE, in the Status field choose to Enable
BLACKOUT MODE (turn the LEDs off) or Disable BLACKOUT
MODE (turn the LEDs on).
3 Click OK in the BLACKOUT MODE frame.
You can also enable/disable blackout mode through the
Bridge’s front-panel switches (refer to Section 3.10.1.2)
3.8 System Date and Time
NOTE: The SYSTEM
DATE AND TIME
screen f eatures an infor-
mational timestamp.
The refresh function of
your browser updates
this timestam p.
To change the date and time on the Bridge:
1 Log on to the Bridge GUI admin account and select SYSTEM
OPTIONS from the menu on the left.
2 At the top of the SYSTEM OPTIONS screen, under SET SYSTEM
TIME, enter the time and date, using two-digit values,
according to the format:
hh:mm MM:DD:YY.
3 Click Apply at the bottom of the SET SYSTEM TIME frame.
3.9 Restoring Default Settings
The Fortress Bridge’s factory default configuration settings can
be restored in their entirety through the Bridge CLI (refer to
Section 6.4.7) or via the front-panel switches (refer to Section
3.10.3).
After default settings are restored, the Bridge will have to be
reconfigured for use, just as though it were newly installed, out
of the box.
Because the Bridge’s configuration settings could themselves
be sensitive, Fortress Technologies recommends restoring
them to their default values whenever the Bridge is to be
shipped (or otherwise transported) out of a secured location.
detail:
detail:
- Secure Wireless 1
- Access Bridge 1
- Fortress Bridge 3
- Table of Contents 5
- Configuration 21 6
- Administration 52 7
- Command-Line Interface 80 8
- Chapter 1 11
- Introduction 11
- 1.2 Network Security Overview 12
- 1.3.3 System Components 13
- 1.3.4 Operating Modes 13
- 1.3.5 Deployment Options 14
- 1.4 This Document 15
- Chapter 2 16
- Installation 16
- 2.2 Preparation 17
- 2.2.2 Preparing the Network 18
- 2.2.3 Port Locations 18
- WARNING: The 19
- WARNING: To 19
- WARNING: If the 20
- 2.3 Installation Instructions 21
- 2.4 Outdoor Installation 21
- Clear for WAN Port 23
- CAUTION: The 24
- Non-Root, and click Apply 25
- 2.4.3 Weatherizing the Bridge 26
- 2.5 Indoor Installation 29
- 2.5.2 Configuring the Bridge 30
- Chapter 3 31
- Configuration 31
- 3.2 LAN Settings 32
- Multicast field 33
- 3.3 Radio Settings 34
- ANT1); Radio 2 uses an 35
- CAUTION: 36
- Distance setting on the 37
- Preamble setting of Short 37
- Preamble setting of Long 37
- 100 milliseconds 38
- AP radio mode on the VIRTUAL 40
- Edit button for each VAP 40
- RADIO SETTINGS screen.) 41
- Cleartext Security 42
- Fortress Security 42
- Open WEP and Shared WEP 42
- 802.1X Security 43
- WPA-PSK or WPA2-PSK be used 44
- WPA-Mixed-PSK) 44
- Edit button for 44
- 3.5 Bridge Passwords 46
- For security 47
- Normal operating mode meet 48
- 3.6.2 Secure Shell Access 49
- 3.6.3 Encryption Algorithm 49
- 3.6.4 Re-keying Interval 50
- 3.6.5 Access ID 50
- Global and Default Settings 51
- AUTHENTI 52
- CATION SETTINGS to point 52
- Mode field 52
- section of the 54
- Auth Mode, ensure 54
- 3.7 Blackout Mode 57
- 3.8 System Date and Time 58
- 3.10 Front-Panel Operation 59
- BLACKOUT MODE: Disabled), or 60
- Chapter 4 62
- Administration 62
- Allow. Such a device 63
- To edit a device: 64
- 4.2 User Authentication 65
- Local au 66
- To add a user: 67
- To edit a user account: 67
- To delete a user account: 68
- 4.3 Trusted Devices 69
- 4.3.1 Editing Trusted Devices 70
- 4.4 SNMP Settings 71
- 4.5 Backing Up and Restoring 72
- FIPS operating mode 73
- 4.6.1 Viewing 75
- Current Software Version 75
- Performing 76
- 4.7 Rebooting the Bridge 77
- Chapter 5 78
- Monitoring and Diagnostics 78
- 5.1.1 Traffic Statistics 79
- 5.1.2 Interface Statistics 79
- 5.2 Tracking 80
- 5.3 AP Associations 82
- 5.4 View Log 83
- 5.5 Diagnostics 85
- HOST MAC DATABASE: 86
- HOST MAC DATABASE button 86
- 5.6 Front-Panel Indicators 87
- 5.6.2 Radio LEDs 88
- 5.6.3 Port LEDs 89
- Chapter 6 90
- Command-Line Interface 90
- bits per second: 9600 91
- data bits: 8 91
- parity: none 91
- stop bits: 1 91
- hardware flow control: none 91
- 6.2 Getting Help in the CLI 92
- 6.3 Command Syntax 93
- 6.4.1 LAN Settings in the CLI 94
- Enter↵, to display the 95
- NOTE: The Bridge 96
- ANT1), while 96
- NOTE: If you are 96
- Enter↵ to leave the 96
- NOTE: Because 97
- Enter↵ to 99
- NOTE: Pa s s wo r d s 101
- NOTE: Usernames 101
- NOTE: Yo u c a n 102
- CAUTION: For se 103
- CAUTION: If you 104
- NOTE: Disabling 104
- NOTE: The 105
- Enter↵ to save them 105
- NOTE: Tr u s t e d D e 110
- CAUTION: Specify 110
- NOTE: You cannot 110
- FIPS op 110
- NOTE: The term 112
- 6.6.7 Pinging a Device 114
- 6.6.8 Tracing a Packet Route 114
- NOTE: Wir e le s s 115
- NOTE: You cannot 115
- Deployment with SAC 116
- 10.0.0.0–10.255.255.255 118
- 172.16.0.0–172.31.255.255 118
- 192.168.0.0–192.168.255.255 118
- <serialnumber> 123
- Chapter 7 124
- Specifications 124
- 7.1.4 Compliance 125
- 7.1.5 Logical Interfaces 125
- Chapter 8 127
- Troubleshooting 127
- Failed to decrypt 128
- Glossary 138
- Fortress : Glossary 139
© 2020, manymanuals.fr. Tous droits réservés | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels